JUNK RUN

RULE BOOK DISCLAIMER

The rules and/or regulations set forth herein are designed to provide for the orderly conduct of racing events and to establish minimum acceptable requirements for such events. These rules shall govern the condition of all events, and by participating in these events, all participants are deemed to have complied with these rules. NO EXPRESSED OR IMPLIED WARRANTY OF SAFETY SHALL RESULT FROM PUBLICATIONS OF OR COMPLIANCE WITH THESE RULES AND OR REGULATIONS. They are intended as a guide for the conduct of the sport and are in no way a guarantee against injury or death to a participant, spectator, or official.

The race director shall be empowered to permit reasonable and appropriate deviation from any of the specifications herein or impose any further restrictions that in his/her opinion does not alter the minimum acceptable requirements. NO EXPRESSED OR IMPLIED WARRANTY OF SAFETY SHALL RESULT FROM SUCH ALTERATION OF SPECIFICATIONS. Any interpretation or deviation of these rules is left to the discretion of the officials. Their decision is final.

IF IT DOESN’T SAY YOU CAN DO IT, THEN DON’T DO IT!

CARS PERMITTED: Any (4 cyl, 6 cyl, 8cyl) 2wd, AWD, 4x4, rear wheel drive, front wheel drive, example: mini vans, Aerostars, Caravans, Voyagers, S10 Blazers/Pickups, Explorers, Bronco II’s, Rangers, Jeep Cherokees, Volvo’s, Subaru’s, Mazda’s, Toyota Pickups. No full size pickups/suburbans/conversion vans etc. No soft-top vehicles.

INTERIOR/EXTERIOR: Interior striped carpet/ extra seats, door panels, headliners, etc.

BRAKES: Must have brakes in working order (front or rear)

BUMPERS: MUST BE FACTORY STOCK may Re-bolt or weld to frame.

CARBURATER AIR FILTER: Must be in place.

DIFFERENTIALS: You may modify rear end.

DOORS: Weld 5" on 10" off or chain front and back doors also rear hatch.(1/4 chain )

ENGINE MOTOR MOUNTS: Engine may be secured to the frame by any method that does not strengthen any other component.

ELECTRICAL: Battery can remain under hood or be relocated to front passenger floor. If relocated to floor it must be secured firmly to floor and covered with a rubber mat. If you can’t secure properly leave under hood and cover with rubber mat. Solenoids, computers, voltage regulators may be relocated. All fuses must be removed except ones that control ignition gauges and charging systems.

EXHAUST PIPES: Remain stock and at least extend beyond driver’s seat. Stacks are ok. 

FAN BLADES: Must be clutch or electric. Clutch fans must be protected by a fan shroud or fan blade must be removed.

WHEEL WELLS/ FENDERS INNER/OUTER: Must be in place. Not cutting, folding, welding, bending permitted.

GAS TANKS: Can remain stock position (example under rear seat. Secure with ¼” welded chain) or double ratchet strapped (ALL sharp metal MUST be padded for straps) thru floor unless behind rear axle. If necessary you may move tank to the floor behind driver’s compartment. Must be secure (1/4: welded chain) or double ratchet strapped (ALL sharp metal MUST be padded for straps) to floor/bed and covered with firewall.

GLASS: All glass must be removed. Windshield, windows, headlights, taillights, mirrors. All broken glass and debris must be removed from entire vehicle or the vehicle will not be allowed to participate in event.

DRIVER’S AREA: Single bar behind seat or under dash allowed. Nothing up or down to frame or body. (Roll cage/roll over bars permitted not required). Bar/chain required to be bolted/welded from roof down to dash on driver side only (front of steering wheel).

RADIATORS: You may bypass, but must remain in the original factory position with no additional reinforcement. All antifreeze must be drained and replaced with water.

AIR CONDITIONING: Freon must be removed from all air condition units per federal regulation.

HOOD: To prevent hood from opening each must be tied down in 4 positions with chain (1/4: welded chain) Or 4 mounts on hood with max of 1/2 bolts A hole must be cut in the center of the hood 12”x12".

IGNITION SWITCH: Complete ignition switch may be relocated and/or altered providing key or toggle switches are accessible within 16 inches mount on dash only) of the steering wheel. No bare wires.

INTERIOR/EXTERIOR: All carpet, visors and all rear seats/cushions must be removed. All dirt/loose material (mirrors, wheel covers, sharp hood ornaments, plastic grill parts, trailer hitch & brakes, soft chrome moldings and pieces of glass) must be cleaned out of vehicle.

SUSPENSION: Vehicle must sit level at stock height. Frozen shocks are illegal. Must move up and down a total of 6 inches of suspension deflection by one man’s effort.

TIRES: Any ply tire.

TRANSMISSION: Mount may be reinforced. Floor shift allowed. Must have a non-sharp end on shifter. Must have all sharp edges in floor shift used. Lines may be by-passed.

Safety belts, eye protection, and DOT helmets are required AT ALL TIMES ON THE TRACK. Long sleeve shirts and pants must be worn – shorts are not acceptable.

JUDGES DECISION IS FINAL – WE RESERVE THE RIGHT TO REJECT ANY AND ALL ENTRIES.